BenchMade steel 蝴蝶钢材

切断 · 发表于 2010-6-19 18:26

让你们可以选两项

When it comes to blade steels, Benchmade not only selects premium grades for their natural qualities, but we also have perfected our own proprietary custom heat treat process which maximizes each steel's edge toughness and cutting performance.
Bohler M390: A high performance blade steel with superior cutting ability and wear resistance due to its high concentration of vanadium and chromium carbides. Its unique powder metallurgical process also promotes a uniform carbide distribution and clean steel properties, making M390 a popular steel used in surgical cutting instruments and in applications requiring a high finish. As a blade material it offers excellent corrosion resistance due to its high concentration of Chromium.
More info: www.bohler-edelstahl.com/files/M390DE.pdf
Bohler N680: A chromium-molybdenum conventionally produced stainless steel with the addition of vanadium and nitrogen. Excellent corrosion resistance properties, especially in salt water. Good hardenability and high obtainable hardness. High wear resistance and ability to preserve keenness.
N690: An Austrian made stainless steel, which is comparable to 440C in performance and value. Keen edge qualities with great corrosion resistance.
CPM-M4: Special purpose, high-speed steel with a combination of high Carbon, Moly, Vanadium and Tungsten for excellent wear resistance and toughness; A powder-metal, non stainless steel.
154CM: An American made premium grade stainless steel originally developed for tough industrial applications. Known for its best all-around qualities, it offers great corrosion resistance with good toughness and edge quality.
S30V: An American made and developed premium grade stainless steel created especially for knives. It is a powder made steel with a uniform carbide distribution and clean steel properties. As a blade material it offers excellent corrosion resistance and superb edge qualities.
D2: An air-hardened tool steel, which offers good corrosion resistance and excellent mileage in wear resistance. A good choice for hard use applications.
440C: A high-chromium stainless steel with a terrific balance of good hardness and corrosion resistance. 440C takes a nice edge and is fairly easy to resharpen. An excellent value priced steel for its performance.
X15: This French steel was developed for the aircraft industry for jet ball bearings, as well as the medical industry for scalpels. It has the ability to resist rust in the worst of conditions while maintaining ample edge retention. The capability behind this steel is in the way it is manufactured, resulting in the finest steel for use in harsh environments such as salt water. The edge on an X15 T.N blade is easier to maintain.
AUS-8: A Japanese made medium-carbon, high chromium stainless steel, which offers a good balance of toughness, edge sharpness and corrosion resistance.
9Cr13CoMoV: A Chinese made high-carbon stainless steel with increased levels of cobalt added for greater edge retention. Offers a higher level of corrosion resistance at a great value.
8Cr14MoV: A Chinese steel with similar performance characteristics to AUS-8. An excellent value priced steel for its performance.
DAMASCUS: A specially forged, layered steel made up of a variety of steels, It offers remarkable toughness and edge quality. For finishing, the surface layers or lines are exposed through an acid etch, which creates a very unique visual effect. Used in special applications due to its inherent high cost and artistic nature.

恩，貌似我抄袭了不少东西（反正这些东西是公开的），原网页是：http://www.benchmade.com/about_knives/our_blades.asp

切断 · 发表于 2010-6-19 18:27

点击图片，看得更清楚！

nevin · 发表于 2010-6-19 18:32

不用投票了，没什么钢材特别不适合EDC的。

切断 · 发表于 2010-6-19 18:35

这个贴是纯喜爱投票
抛开硬度、保持性、韧性（因为edc基本上用啥都行）
你喜欢啥，就投啥
比如一把710，你要是收，收什么钢的，你就投啥

onelight · 发表于 2010-6-19 19:01

蝴蝶听老大们说过，154cm最好！

饭太热 · 发表于 2010-6-19 19:01

本帖最后由饭太热于 2010-6-19 19:11 编辑

个人钟爱30V，因为印象深刻，而且接触的多，再就是154CM了，最后是D2。
刀友手中的刀分两类，一，工具。二，个人爱好收藏艺术品。作为工具，其价值就是完成工具的使命达成使用的目的，而工具本身最后的结果是不重要的，基本上只要不傻，都会用刀。而作为收藏呢，讨论吧，，YY吧，花钱吧~~~哈哈

忘了说理由了。
对于判断某物品好与坏之前都需要一个判断的标准。我判断的标准就是：S30V,154CM,D2的刀在夏天放在裤兜里，这样高湿度的环境下EDC了几个星期都没有生锈，不错。而平时干粗活就是开包装，细活就是修修指甲上的肉刺，能这样反复的使用，可以说是保持性也不错。最后，从来没丢过刀，哈，运气更是不错~对于在外面吃饭时用刀的话如果不是在国外的话尽量少这样（聚会包间内除外），您可以无视我的话，但请对你的行为负责。
谢

切断 · 发表于 2010-6-19 19:11

个人钟爱30V，因为印象深刻，而且接触的多，再就是154CM了，最后是D2。
刀友手中的刀分两类，一，工具。二，个人爱好收藏艺术品。作为工具，其价值就是完成工具的使命达成使用的目的，而工具本身最后的结果是不重要 ...
饭太热发表于 2010-6-19 19:01

不客气，你现在不是在野外么？谈谈野外EDC

饭太热 · 发表于 2010-6-19 19:14

不客气，你现在不是在野外么？谈谈野外EDC
切断发表于 2010-6-19 19:11

不好意思，其实我在潘多拉。

切断 · 发表于 2010-6-19 19:44

不好意思，其实我在潘多拉。
饭太热发表于 2010-6-19 19:14

没关系，你现在在用什么牌子的骨头刀呢？

lsjalain · 发表于 2010-6-19 19:51

本帖最后由 lsjalain 于 2010-6-19 19:53 编辑

蝴蝶我只玩过S30V，154CM和ATS-34，其实用起来没感觉到太大的区别。估计磨刀的高手能感觉到个中差异，我用起来感觉都蛮锋利的，都很喜欢。
我选择刀的时候似乎对钢材不是很讲究，用碳钢砍刀的时候真的觉得太会锈了，不过反正也不用来处理食物，有点锈不妨碍砍柴。

饭太热 · 发表于 2010-6-19 21:35

没关系，你现在在用什么牌子的骨头刀呢？
切断发表于 2010-6-19 19:44

你错了吧，潘多拉星球上的动物的骨骼都是高强度碳纤维的。。。
最近EDC是蜘蛛的紫色C11，色彩绚丽，够锋利。

成事在刃 · 发表于 2010-6-19 21:50

首先要选154CM,蝴蝶这种钢很常用很有名,再一个我选440C,保持性算不错的钢,价格便宜,性价比高,而且这种钢我接触最多,有些感情.

切断 · 发表于 2010-6-19 22:43

你错了吧，潘多拉星球上的动物的骨骼都是高强度碳纤维的。。。
最近EDC是蜘蛛的紫色C11，色彩绚丽，够锋利。
饭太热发表于 2010-6-19 21:35

不是说阿凡达骨骼强度堪比高强度碳纤维么？

godbob · 发表于 2010-6-20 02:10

我投了151CM。
而且，当时舍了F1而取了151，因为它是蝴蝶的154CM。

cqhb · 发表于 2010-6-20 10:14

我对D2很有好感
当初用了一把卡米拉死的CUDA MAX5.5大折刀，用的就是D2，两年下来一次都没有保养过，居然保持性非常不错，并且没有任何生锈痕迹。后来用D2的710，也是一样

琴瘦 · 发表于 2010-6-20 12:13

我还是赞S30V，但是还是跟你们的想象有差距，好，没那么好

阳光猪 · 发表于 2010-6-20 12:23

本帖最后由阳光猪于 2010-6-20 12:24 编辑

波勒的粉末钢是世界质量最好的。
它的生产设备是世界最先进的，纯度最高。
买它的刃材准没错。

孤帆远影 · 发表于 2010-6-20 16:12

Bohler M390和latrobe的20-cv差不多
sog做过测试，20-cv比s30v,bg42强很多

切断 · 发表于 2010-6-21 00:22

从以上投票结果来看
bm的154cm确实受人欢迎，得到了大众的普遍认可
所以说，喜欢bm的人最好有一把154cm钢的，毕竟bm号称量产中处理154cm最好的厂子

另外，希望bm能使用cpm-154cm

喁喁收集 · 发表于 2010-6-21 20:57

你错了吧，潘多拉星球上的动物的骨骼都是高强度碳纤维的。。。
最近EDC是蜘蛛的紫色C11，色彩绚丽，够锋利。
饭太热发表于 2010-6-19 21:35

握手，同为平磨紫色C11
不过做工超级烂

[量产刀] BenchMade steel 蝴蝶钢材

http://www.funsn.com.cn/

http://www.hcmkj.cn/

http://www.gecbbs.cn/

http://www.17808.cn/

http://www.cstarlight.cn/

[量产刀] BenchMade steel 蝴蝶 钢材